MakerLab创客实验室 — Let's Make something.
现在注册
已注册用户请 登入
LIDICOYU large avatar
MakerLab创客实验室  ›  问题解答

Ultimaker's v1.5.7 PCB+mega2560 R3的固件的问题.

By LIDICOYU at 2 年前 , 1603 次浏览

请大神帮忙:我想DIY一台3D打印机:Ultimaker's v1.5.7 PCB+mega2560 R3,能不能用于三角洲式的打印机.我购的配件想用来做三角洲式的打印机的.我刷了您们的固件 ,机器还是动不了,不知什么原因,特来请教,请给予解决方法.不胜感激.

5 回复
Andy medium avatar
#1 - 2 年前
Andy

可以用于三角洲,直接烧我的固件是不行的,需要做配置才可以。

至少应该把板子类型改为Ultimaker的板子类型。

Andy medium avatar
#2 - 2 年前
Andy

改好板子类型只是前提,还需要做好其它配置才可以。你要下载我的delta固件:
https://github.com/MakerLabMe/Marlin_delta/archive/makerlab.zip
然后修改板子类型:

//// The following define selects which electronics board you have. 
//Please choose the one that matches your setup
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
// 11 = Gen7 v1.1, v1.2 = 11
// 12 = Gen7 v1.3
// 13 = Gen7 v1.4
// 2 = Cheaptronic v1.0
// 20 = Sethi 3D_1
// 3 = MEGA/RAMPS up to 1.2 = 3
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
// 4 = Duemilanove w/ ATMega328P pin assignment
// 5 = Gen6
// 51 = Gen6 deluxe
// 6 = Sanguinololu < 1.2
// 62 = Sanguinololu 1.2 and above
// 63 = Melzi
// 64 = STB V1.1
// 65 = Azteeg X1
// 66 = Melzi with ATmega1284 (MaKr3d version)
// 67 = Azteeg X3
// 68 = Azteeg X3 Pro
// 7 = Ultimaker
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
// 77 = 3Drag Controller
// 8 = Teensylu
// 80 = Rumba
// 81 = Printrboard (AT90USB1286)
// 82 = Brainwave (AT90USB646)
// 83 = SAV Mk-I (AT90USB1286)
// 9 = Gen3+
// 70 = Megatronics
// 701= Megatronics v2.0
// 702= Minitronics v1.0
// 90 = Alpha OMCA board
// 91 = Final OMCA board
// 301 = Rambo
// 21 = Elefu Ra Board (v3)
// 310 = Mega Controller by MakerLab

#ifndef MOTHERBOARD
#define MOTHERBOARD 7 //ultimaker 配置为7
#endif

simon medium avatar
#3 - 2 年前
simon

改好板子类型只是前提,还需要做好其它配置才可以

simon medium avatar
#4 - 2 年前
simon

请问还需要做哪些配置,能否详细贴出教程,谢谢 大神